BMW 3 Series E90 / E91 / E92 / E93 3D-printable parts

This model replaces the chrome cap of the BMW coupe E92 extender arm with a hook that grabs the seatbelt successfully much more often than the original design. Designed to be a near perfect fit with the OEM shape. I recommend printing in ASA or ABS for the high temperatures in a car. The OEM piece easily comes off with a pry tool, then you can attach the 3d printed models with a strong double sided adhesive ( Confirm normal seat, belt and presenter movement and keep the printed part outside the restraint load path.

Adjusted the model for it to fit perfectly without cutting imporant parts of the car. Only thing to remove is the bracket where the electrical conntection for the ashtray connects to. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Use ABS preferably but it wont get that hot up top where this print is located so anything will work Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Shift knob designed for e90 but may fit others. Clips on and does not rotate (careful of breakage if you try to twist it!) Fits fine, but is a bit light. Would be a nice print in transparent colors. Difficult to remove without breaking the teeth! (the knob teeth not yours) Please share your makes :) Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

I created this for my 2011 E91, but it may fit others. Just pull the other parts out of the vent and snap this one on. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Socket for removing oil filter from BMW N52 engine. Adapts to 32mm 6 or 12-point socket. Likely works on other BMW engines as well - I just don't know which ones. I printed out of PETG and had no issues. Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

The dashboard panel around the start button in my e92 began falling off due to a failed clip. I left it like this for quite awhile then the passenger door wood panel also fell off so I decided to design both clips to replace the broken ones as they cost more money than im willing to pay for original and aem ones dont last one use. I printed them with support on their sides so the opening is going up and down as this doesnt rely on layer adhesion for strength. "dash clip 1" is the dash clip "clip 3" is the door clip Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Hello, does your sunroof deflector make a weird noise or doesn't allow your sunroof to close sometimes. Well a section of it may be broken. Both of the side stoppers on my deflector were broken so i printed a replacement pieces. Supports are needed, i used roof support as well. Replacement part for OEM BMW handle. Part Number: 54107157449 Supersession(s): 54-10-7-157-449 This product fits 60 vehicle variants. BMW: 11 models, 60 variants between 2004 and 2012. BMW E90 Slipstream Deflector Replacement Clips/Stoppers 2004-2012 by blackjet123 is licensed under CC BY-NC-SA 4.0 CC Use exterior-rated material and verify secure retention and adjacent-panel clearance.

Contour spacer demonstrated with aftermarket side repeaters on BMW bodywork. The creator lists E36 from October 1996, E46 sedan/Touring, E60/E61, E81/E82/E87/E88 and E90–E93 applications. Test one side before mirroring and verify the repeater remains weather-sealed and positively retained.

Replacement plastic grommet used at E30 grille and rear license-plate mounting points, physically compared with the original. The creator also lists E36, E46, E90 and E92 applications; BMWFans confirms grommet 51131840154.

Direct replacement cap for the automatic-headlight rotary switch used in BMW E82 and E88 1 Series, E90/E91/E92/E93 3 Series, and E84 X1 interiors. The keyed hex and rotation stop reproduce the functional interface, and the creator shows the printed knob installed. Reuse the original switch mechanism; no complete headlight-switch assembly is included.

This is a nice update for us with older E90 BMW's This will allow you to mount a universal Inbay wireless charger. This seems to work well and looks like a factory addition. It will take place of the front pocket in the console or the ashtray if it was equipped. This bracket will mount directly inplace of the old insert. Powering up the device: I did not have the ashtray so I was able to wire this into the power of the usb in th back of the console. you can access this easily by removing the rear vent panel. you can also pull out the plastic rear vent tubing with a little force to more room. You will tap into the Brown/ Ground and the Red/ +12V going to the usb in the rear console. LED Light: As an option I have added some holes for the LED light on the side of the charger. you will need to source a thin fiber optic cable and use the included plastic insert to fit the bigger hole. you wi Use automotive-rated wiring and connectors, retain fuse protection, insulate every terminal and verify unobstructed operation.

So I was looking for a fitting cupholder for my BMW E90 tray and couldn't find one which wasn't too big. This one fits to your BMW E90 without the big navi and without the iDrive knob. I made 3 versions which can fit 250ml, 330ml or 500ml cans (Germany/EU). With the big one, the walls might get too thin, read below. It fits very good to the tray, I use it everyday. This was designed to be printed with PLA, if you use ABS you might upscale it. Also, you can print it on the flat surface with my tag without supports. If you like the design, leave a tip :) *** Update 27.06.20 Someone requested a wider hole (currently 57mm) for norwegian 500ml cans. Uploaded another version with 66mm. Walls get very thin and cut, NO guarantee for good results as I won't try it! *** Update 11.07.20 Was shopping a german/EU 330ml can and couldn't fit it. So I made the hole slightly wider (59mm) to fit these. Ha Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

hi this is my custum made for led back cover lights bmw e90 318i valeo lci ligts please use support my paypal is: sezgin9716@hotmail.com thanks :) Confirm body and lamp variant, secure retention, weather sealing and legal lamp operation before driving.

This is a centering tool designed for the precise installation of a SAC clutch disc between the flywheel and the pressure plate on a BMW E90 from the year 2011. Due to its adaptable design, the tool may also be compatible with models from earlier or later production years. To assist with model adjustments or integration, a STEP file of the tool has been provided. The tool was 3D printed using PLA+. Standard PLA should also be sufficient, as the component is not subjected to significant mechanical stress during use. After successfully mounting the preloaded SAC pressure plate, the centering tool must be removed before installing the transmission. This can be done by pulling it out using a screw or a pair of pliers. Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

I used petg for this use organic supports Use fluid-, heat- and UV-resistant material and verify full wiper and washer clearance.

I added a 29mm cigarette lighter hole and a bmw logo on top of Fix3D:s model. You should probably use the original model's slicer settings. I used mostly default settings and the print could have come out better:) The bottoms of the holes are pretty thin and the other one broke on me while removing from the print bed, so I printed some BMW coasters with a diameter of 65mm and put them in the holes to hold the drinks. Printed in PETG basic Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Just a replacement washer fluid reservoir cap for a BMW E92. Insert included if you would like to print in a contrasting colour. Recommend printing upside-down, flat on the print surface. I know these are cheap to buy but “I can 3D print that!” Use fluid-, heat- and UV-resistant material and verify full wiper and washer clearance.

A friend of mine has an E90 and lost the clips that hold the (rear) window shades in, he was looking everywhere for them and couldn't find any at a reasonable price so I had a crack and modelling and printing them for him. They're pretty close to the original design and have similar properties when printed with PETG. I thought I'd share the model in case anyone else is also struggling to find them. If you encounter any issues let me know and I'll tweak the design for you. I'm unsure of their BMW part number, but the sun shade is 51462359741 . Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

This replacement clip is designed for the BMW E9x M3 (E90, E92, E93) center console shifter boot. If your shifter boot keeps detaching or won’t stay secured, this clip is the perfect solution. Installation: This clip must be glued in place where the original clip was broken off. Once installed, it restores a snug fit and keeps your shifter boot securely attached. Features: Perfect Fit: Precisely modeled to match OEM dimensions for a secure hold. Durable Material: Recommended to print in PETG or ASA for strength, heat resistance, and longevity. Easy Repair: Simply glue it where the original clip was — no modifications needed. OEM-Style Design: Matches original fit and function without compromising appearance. Compatibility: BMW E90 M3 BMW E92 M3 BMW E93 M3 Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Connector housing for retrofitting door courtesy-light projectors to a BMW E90 that was not equipped with the factory lighting package or wiring. Two models are included to fit the courtesy-light unit; the creator used the larger version. For the electrical connection, the creator used the female side of an electronics pin header at the lamp and soldered positive and negative wires to the male side, insulating the joints with heat-shrink tubing. An editable SketchUp file is included. Use automotive-rated wiring and connectors, retain fuse protection, insulate every terminal, and verify unobstructed door and window operation.

MAF adapter for a 335d to a 4" flange cone filter. Takes the oval and turns it into a circle for mounting a cone filter. I used RTV silicone to attach it to the MAF (it's a very tight fit), once it sets clamp on your filter. Designed so the air is funneled in... Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

This is clutch alignment tool for BMW self-adjusting clutch. I used it on 2007 BMW E93 with M57 engine, but it could be used on other BMWs with SAC. You will need M6 bolt to use this tool. I print it with 50% infill using PETG, but PLA should work just fine, as you shouldn’t need much force to pull the tool out if you installed and torqued everything correctly. It has been printed on Prusa MK3S printer. Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

This connector moves all the louvers in the vent together. Originally is made of metal and super thin. Printed with 100% infill Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.