Mechanical — 3D-printable BMW parts

Replacement beauty cap for M50, M52 and M54 engine-cover fasteners, physically shown on the engine. BMWFans identifies the exact component as cap 11121726089 and confirms E34, E36, E38, E39, E46, E53, E60/E61, E65/E66, E83, E85 and Z3 applications. Use engine-bay-rated material and keep it clear of hot or moving parts.

Front intake air scoop for N55-powered BMW F30/F31 335i, F32-series 435i, F20/F21 M135i and F22/F23/F87 M235i/M2 applications listed by the creator. Use heat- and exterior-rated material and verify secure retention and unobstructed intake airflow before driving.

Replacement outer fuel-filter clip designed for a 2015 F30 328d and reported by the creator to have remained installed for more than a year. Use the specified material, inspect layer adhesion and fit, and stop if the part interferes with safe service or pedal operation.

Replacement oil-sump drain-plug access cover for E46 and Z4 E85/E86 undertrays. The creator corrected the screw-hole location and removed reinforcement that caused the physical print to warp. Use an underbody-rated material and verify screw retention, exhaust clearance and complete undertray seating.

Replacement access cover for the oil-drain opening in the engine-compartment underbody screening, physically shown loose and installed by the creator. BMW catalogs identify this child cover as 51757261712, item 5 in the underhood-shield diagram; it is used on X3 F25 and X4 F26 applications, so both live generations are linked. The printed design uses lower U-nuts and hex screws rather than the original fastening method. Print in PETG or a higher-temperature engineering polymer, confirm the panel variant and VIN, and verify secure retention and clearance before driving.

Two replacement retainer geometries for repairing broken attachment tabs on the BMW X1 E84 engine air-filter housing. The creator links the original repair write-up and supplies physical comparisons, loose parts and installed engine-bay views for both shapes. The printed pieces repair features of the larger air-filter housing rather than reproducing a separately serviced BMW child component, so no housing parent number is assigned. Print in PETG as documented or a higher-temperature engineering polymer, fasten exactly as shown, and verify intake sealing, bonnet clearance and retention after heat cycling.

Dual catch-can mounting bracket designed by the creator for the S63TU engine bay in the BMW F13 M6 and F10 M5. The creator links an installation video for the twin-turbo M6 setup, providing physical-use evidence beyond the preserved CAD render. Print in a heat-resistant engineering material such as nylon, keep clear of hot or moving components and hoses, and inspect retention after initial heat cycles. This is an aftermarket accessory with no original BMW component counterpart, so no OEM number is assigned.

Replacement throttle-body linkage/cable nipple for the M10-powered BMW E28 518i; two identical pieces are required in the catalog assembly. The design is based on an original part and includes print-orientation guidance. BMW number 13541286378 is cataloged specifically for E28 518i M10 applications and selected M10-powered E30 models, not every E28 engine.

Use ABS preferably but it wont get that hot up top where this print is located so anything will work Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

MAF adapter for a 335d to a 4" flange cone filter. Takes the oval and turns it into a circle for mounting a cone filter. I used RTV silicone to attach it to the MAF (it's a very tight fit), once it sets clamp on your filter. Designed so the air is funneled in... Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

This is a fix that I made for my 2007 BMW 320D air intake back in 2014. The M47N2 engine air intake hose has rubber ends which start to break over time, so instead of spending >30€ on a new OEM part (13717795284), I decided to make a fix of my own, as I had a 3D printer at home at that time. People keep asking me for the STL, and since I no longer have my own server, I decided that it's time to upload it here. NOTE: it's a tight fit so you'll most likely have to remove the whole 3 connecting parts of the intake as a single unit when trying to get to the engine (only 4 screws though, so it's not a big deal). Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Two-piece M54 engine air-intake duct physically fitted to the E46. BMWFans, RealOEM and Hubauer cross-confirm genuine BMW intake tube 13717509118 for the matching M54 and M56 applications. Use a heat-resistant engine-bay material and verify air-box sealing, bonnet clearance and freedom from belts and fans.

80 mm intake adapter for vacuum or smoke leak testing on the E46 M54B22, designed around a standard automotive valve and physically demonstrated on the engine. Use only at low diagnostic pressure, keep foreign material out of the intake and remove the adapter before starting or driving the vehicle.

This is a nut for the engine cover as seen in the second image. It works for e46 316i,318i and 320i, possibly for other models that have the same nut. Note: you will need an O-ring or rubber washer (⌀10mm) to prevent unscrewing due to the engine vibrations, the original nut has one too. You'll need ABS filament or PET-G, PLA filament will break after a couple of months. Print Settings Printer Brand: Artillery Printer: Artillery Hornet Rafts: Yes Supports: No Resolution: 0.2 Infill: 25 Filament: ABS or PET-G Notes: minimum 3 perimeter for Vertical shells Category: Automotive Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Replacement air-intake suction tube for 1999-2001 E46 M52 models, physically installed by the creator. BMWFans, RealOEM and Hubauer cross-confirm genuine BMW component 13711438768 for the matching E46 320i/320Ci, 323i/323Ci and 328i/328Ci applications. Print in a heat-resistant engine-bay material and verify sealing and clearance.

Two-piece intake opening developed and physically fitted to the airbox of a BMW F20/F21 1 Series. The creator states that it is intended to add intake sound, not power; the cutting profile and finished insert are both included. Keep the factory filter path intact, use an engine-bay-temperature-resistant material, de-burr the airbox opening, and inspect the installation for secure retention and contamination paths before running the engine.