BMW 3 Series F30 / F31 / F34 / F80 3D-printable parts

Replacement slider for the factory BMW wireless-charging cradle that increases usable phone length to approximately 168 mm. The creator documents F2x, F3x, F8x, and I01 cradle compatibility and shows the printed part installed and measured. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material; verify latch engagement, charging operation, and secure phone retention before driving.

Small storage bin fitted beside the handbrake lever in a BMW F30 328i. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Scanned right-side F30/F31 headlight support bracket shown fitted in place by the creator. Use exterior-rated material and verify retention, weather sealing, lamp aim and washer operation before driving.

Front intake air scoop for N55-powered BMW F30/F31 335i, F32-series 435i, F20/F21 M135i and F22/F23/F87 M235i/M2 applications listed by the creator. Use heat- and exterior-rated material and verify secure retention and unobstructed intake airflow before driving.

Vent support for a Quad Lock phone interface, physically demonstrated on the right-hand-drive driver's-side center vent shared by the creator-listed BMW F30, F31 and F32. Fitment is limited to those bodies and RHD placement; F33/F36 and LHD fitment are not inferred. Use cabin-heat-resistant material, tighten without damaging the vent, and verify full vent, display, control and sightline clearance before driving.

Replacement outer fuel-filter clip designed for a 2015 F30 328d and reported by the creator to have remained installed for more than a year. Use the specified material, inspect layer adhesion and fit, and stop if the part interferes with safe service or pedal operation.

TPU clutch-stop set in 10, 12, 14 and 16 mm heights for manual BMW F3x models; the creator reports the 16 mm version installed with the factory clutch. Use the specified material, inspect layer adhesion and fit, and stop if the part interferes with safe service or pedal operation.

Clip-on shopping-bag hook demonstrated on the factory rear parcel-shelf cover of BMW F31 and G31 Touring models. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Parametric insert demonstrated in the sliding-cover cup holder used by BMW F30/F31 and F32/F36 LCI interiors. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

4.5 mm depth adapter for installing a BLAM BM200W 200 mm subwoofer in the original HiFi enclosure of a BMW F34 3 Series Gran Turismo. Use cabin-rated material, isolate wiring and connectors, and verify secure fit and unobstructed speaker operation.

Two-piece open- or closed-loop umbrella mount demonstrated on the inside of an F31 Touring boot lid. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

F30 cup-holder organizer for a garage-door remote, coin, keys and other small cabin items. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Small removable coin cup printed for the recessed BMW F30/F31 center cup holder. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Cup-holder insert that steadies slim beverage cans and raises a small fragrance tin for easier removal in BMW F3x interiors. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Adapter for installing a universal 100 mm speaker in the original BMW F30/F31 speaker location. Use cabin-rated material, isolate wiring and connectors, and verify secure fit and unobstructed speaker operation.

Funnel sized for the BMW F30 washer-fluid filler neck and physically shown in the engine bay. Use fluid-, heat- and UV-resistant material and verify full cap, hose, bonnet and washer clearance.

Replacement storage tray for the center-console cavity left after removing the factory phone cradle in a 2013 BMW 320. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Round and splined clutch-alignment tool variants designed for BMW N55 cars with the GS6 manual transmission. The creator printed the tool for a 2015 F22 M235i clutch replacement and verified the splined version during installation. Source fitment also names N55 E82, E9x, F3x, F10/F11, and F22/F23 cars. Use only on the specified engine/transmission combination, compare pilot and spline dimensions before use, and do not treat the printed tool as a torque-bearing service tool.

Cup-holder phone stand with a Lightning-cable passage, documented by the creator for BMW F20 1 Series and F30/F31 3 Series interiors. The gallery shows the stand installed, holding phones, and routing the charge cable. Add a thin foam or rubber liner as suggested, use a heat-resistant cabin material, and confirm secure phone retention before driving.