BMW 1 Series E81 / E82 / E87 / E88 3D-printable parts

Cup holder developed and physically installed for a first-generation BMW 1 Series interior. The retained files are the latest creator-supplied right- and left-hand supported variants; earlier revisions are preserved in the source archive but are not submitted. Use a heat-resistant cabin material and confirm local clearance before driving.

Three-piece service-tool set for BMW N42, N46, and N46T engines: intake camshaft lock, exhaust camshaft lock, and the creator's strengthened M8-bolt VANOS gear counter-holder. The creator reports using the tools repeatedly and revised the counter-holder for the specified tightening procedure. This is an engine-specific workshop aid, not a substitute for BMW service information: inspect every print before use, follow the applicable repair procedure and torque sequence, and stop if any cracking or deformation is visible.

Direct replacement cap for the automatic-headlight rotary switch used in BMW E82 and E88 1 Series, E90/E91/E92/E93 3 Series, and E84 X1 interiors. The keyed hex and rotation stop reproduce the functional interface, and the creator shows the printed knob installed. Reuse the original switch mechanism; no complete headlight-switch assembly is included.

Three-piece cup-holder assembly tested in a 2010 BMW E87. It relocates the drink above the original low cup recess so taller containers can be used without the armrest interfering. The retained package contains the adapter, bridge, and cup cradle. Use a heat-resistant cabin material and verify secure engagement before driving.

Two-piece removable cup holder for early BMW 1 Series door pockets. A separate interference-fit hook supports the holder in the door pocket; the creator sized it for takeaway cups and drinks cans and supplied a physical print photograph. Print in PETG or ABS for cabin heat resistance and confirm retention before driving.

36 mm, half-inch-drive oil-filter housing socket physically tested on the M47 diesel engine in a BMW E87 1 Series. The creator printed it at 90% infill, shows it seated on the filter cap, and reports successful use. Use a tough material, inspect the drive and hex surfaces before use, and replace the print if it shows cracking or rounding.

Two-piece replacement for the left dashboard air-vent position in a BMW E87, combining the vent housing with a round gauge/display holder. The creator's gallery shows the assembly installed in the vehicle. Confirm the instrument diameter and preserve safe driver visibility before installation.

Cup holder and 50-cent shopping-token recess for left-hand-drive first-generation BMW 1 Series centre consoles that lack the factory holder. The creator installed the printed assembly with double-sided tape and reports secure use. Both the single-piece model and the split top/bottom alternative are retained. PETG or ABS is recommended for summer cabin temperatures.

Phone-mount bracket for the factory accessory cup-holder socket in BMW E81, E82, E87, and E88 interiors. The current creator photographs show the bracket installed with a circular magnetic phone interface and also show the loose physical print. Only the bracket is included; choose compatible phone hardware and confirm that the device does not obstruct controls or driver visibility.

Round and splined clutch-alignment tool variants designed for BMW N55 cars with the GS6 manual transmission. The creator printed the tool for a 2015 F22 M235i clutch replacement and verified the splined version during installation. Source fitment also names N55 E82, E9x, F3x, F10/F11, and F22/F23 cars. Use only on the specified engine/transmission combination, compare pilot and spline dimensions before use, and do not treat the printed tool as a torque-bearing service tool.

Flexible replacement for BMW rubber buffer 51466967605, creator-tested on an i3 and catalogued for F45, E81/E87, F20/F21, I01, and X1 E84. Print in approximately 85A TPU and cut out the temporary support tab after printing. Within the combined E8x generation, documented fitment is E81/E87 only.

Replacement clip for BMW door-sill/entry trim panels. The creator explicitly lists E21, E30, E36, E39, E46, E81/E82/E88, F20, E85 and related applications and identifies genuine BMW clip 51471840960. Verify the receiving-hole and trim thickness before fitting.

Contour spacer demonstrated with aftermarket side repeaters on BMW bodywork. The creator lists E36 from October 1996, E46 sedan/Touring, E60/E61, E81/E82/E87/E88 and E90–E93 applications. Test one side before mirroring and verify the repeater remains weather-sealed and positively retained.

Four clip-in replacement gear-knob shapes for the BMW E34 and the creator-listed classic BMW chassis. The design was developed around the common BMW latching stem and includes an installed physical example. Confirm the lever's clip profile and preserve full shift travel before driving; the grouped API fitments reproduce only chassis families explicitly listed by the creator.